Most of the people ask about how to install dryer vent in wall. Therefore, in this article, we will guide you how to install dryer vent in wall. Installing a dryer vent is a very simple and uncomplicated product for the do-it-yourselfers.
Before you buy supplies or make any preparations, remember that the smoother, shorter, and less restricted working of the vent , the faster your garments will dry. Shorter operating times also imply that the dryer needs to operate less, which means that your garments will wear out faster. Also, keep it in mind that lint buildup can cause safety concerns, therefore you should install the dry vent so that it can be used to sweep out lint.
If you’re merely putting a new dryer in the same area as the previous one, it may be as simple as connecting the new appliance to the existing venting. A new vent installation, on the other hand, requires a bit more labor and forethought. Before deciding on a type of ducting, read the manufacturer’s instructions. Flex ducting, for example, is not advised for use with some dryers.
How To Install Dryer Vent In Wall - Complete Guide
Tools And Equipment
- Vent on the wall
- Caulking gun
- Duct tube for a dryer
- For joints, use clamps or aluminum tape.
- Straps for pipes (for long runs)
- elbows for venting
- Caulk for the outside
Instructions:
Basic Preparations:
Determine the shortest and most direct path for the dryer duct. Make a list of the items you’ll need and the length of ducting you’ll require. Depending on the type of ducting you use, check the manufacturer’s guidelines for the maximum length of the duct. Subtract 4 to 10 feet from the maximum duct length for each elbow you want to utilize. Because installation varies from model to model, see the manufacturer’s instructions. According to certain building rules, the maximum ducting length is 25 feet, with 5 feet deducted for each elbow.
Install The Wall Vent:
Measure first, and then drill a pilot hole before committing to a certain spot. Check that the broader final hole (4 1/2 inches wide) will not cut through a stud, joist, or sill plate after drilling the pilot hole.
You’ll need to drill a 4 1/2-inch-diameter hole in the house’s side. This is simplest to drill with a big hole saw, unless it is a stucco wall, in which case you may outline the opening for the duct and then break it out with a succession of little holes. If you don’t have a hole saw, a reciprocating saw or jigsaw can be used to construct this cut-out.
After cutting the hole, the vent tailpiece is placed from the outside, screwed into position, and caulked using an external caulk.
Measure The Vent And Cut It:
Calculate the distance between the dryer and the vent. Set up any elbows or bends you may have and take your measurements. If you are utilizing stiff ducting, you should measure and cut it to size before joining the seams. Handle rigid ducting with caution since it is extremely sharp, especially after it has been cut. Protect your hands by wearing gloves. After cutting the ducting to size, align the seams by beginning at one end and pulling both sides down and in, forcing them together.
Tip
Rigid ducts have male and female ends. When connecting, ensure that the male end is towards the outside vent. This prevents lint from accumulating at the connectors.
Join The Duct:
If you’re using aluminum flex ducting, roll the rounded edges of the flex on the concrete using a piece of pipe. This will flatten the ends, making them easier to slot onto the dryer vent tailpiece and the wall vent. Once the ducting is in place, tighten both ends with clamps. If you’re using stiff ducting, secure it to the vent outlet and dryer tailpiece using aluminum tape.If there are lengthy sections of ducting, strap it to the wall or ceiling joists for support; don’t rely on the seam tape to sustain the weight of the ducting.
Check The Dryer:
Double-check that the ducting did not become kinked or detached when the dryer was placed into place. Run the dryer to ensure that all of the connectors are connected and that the duct louvers on the exterior of the home are open.
If you face any difficulty in installing a vent on the wall, you may contact dryer vent installation and repair Gainesville, GA. They are best known for their excellent services and affordable rates.
Can I Make A Dryer Duct Out Of PVC?
PVC dryer vents are often less expensive than metal dryer ducts. They are, however, less durable and likely to gather lint, so you will need to clean them more frequently. They’re also not as safe as metal ducts since they can bend, preventing air from leaving easily and posing a fire threat. Overall, if you have the money, it’s preferable to go with a metal dryer duct.
Is It Necessary To Vent A Dryer Outside?
The power source determines whether you need to vent your dryer inside or outdoors. We can directly vent Electric dryers inside, making them an excellent alternative for renters and those who do not have an appropriate external entrance in their house.
If you have a gas-powered dryer, it must be vented outside. Because gas dryers emit carbon monoxide as a byproduct, venting them indoors is exceedingly hazardous. If you choose, you may also vent an electric dryer outside. However, if you install an outdoor vent, you need to schedule regular cleaning of the vents. For professional cleaning, you may contact dryer vent cleaning Gainesville, GA.
Can We Directly Exhaust Our Dryer Vent?
If the construction of your home and the placement of your dryer allow it, you may install a dryer vent directly through an outside wall. It’s typically better to do so. Venting a dryer via the wall eliminates the need for bends in the vent pipe and allows you to keep the pipe as short as feasible. The advantage of this is that it decreases the possibility of the vent being clogged.
Conclusion:
In conclusion, we can say that dryer duct installation is a very easy process. However, you need to be very accurate and attentive during the process.
Also Read: What Is An Indoor Dryer Vent And How To Install It With Dryers